Stencil your company logo on your epoxy floor-also add a welcome for your international clients.
Stencil your company logo on your epoxy floor-also add a welcome for your international clients.
ZeroStat Crete Fundamentals

Static-Conductive Water Based Epoxy Concrete Finish

  • Economical, state of the art, permanent conductive formulation.
  • Hard extended wear performance, never requires ESD Wax.
  • Water based, easy application and cleanup
  • Excellent chemical resistance.
  • Extremely cost effective and NOT humidity dependant.
  • Fast, low cost installation, minimal prep requirements.
  • Lowest installation odor in the  industry

ZeroStat Crete incorporates state-of-the-art, static conductive properties into a high performance, two-component, water-based epoxy for use on concrete and other hard surfaces. ZeroStat Crete provides outstanding durability and abrasion resistance while eliminating electrostatic charges which can damage or destroy sensitive electronics components or equipment. ZeroStat Crete also displays superb resistance to a wide variety of chemicals and solvents commonly found in industrial and commercial environments, without the toxicity and disposal considerations associated with some solvent systems. When cured, ZeroStat Crete exhibits characteristics superior to solvent-based polyurethane, and rivaling those of solvent-based epoxy coatings. ZeroStat Crete produces superior results when used on all interior concrete, stone and ceramic surfaces.

SPECIFICATIONS
Spec
Result
Quick Ship colors
Light Gray, Medium Gray
Solids
37% +/- 1%
Static Decay
.02 seconds
PH
6.0 - 7.0
Weight per Gallon
9.5 - 9.6 pounds
Hardness
30 (Sward)
Static Conductive
10^4-10^6 ohms
Viscosity
H - J (Gardner)
Solvents
Water - Glycol
Flash Point
142° F
Dry Time
Touch; 7 hours, Moderate traffic; 12 hours, Full cure 7 days
Coverage
400 - 600 ft2 per gallon
Models and Sizes
Item
Description
Size
ZS-CRETE-Q
ZeroStat Crete
Quart
ZS-CRETE-G
ZeroStat Crete
1 Gallon
ZS-CRETE-5
ZeroStat Crete
5 Gallon
ZS-CRETE-55
ZeroStat Crete
55 Gallon
APPLICATION AND MAINTENANCE
Overview: New concrete floors should be allowed to cure for thirty days. Applications to floors colder than 60° F is not recommended. Sweep and mop contaminated floors with Brut, Grease Strip of Citru-Gest to remove oil, grease and soil. With contaminated or exceedingly smooth troweled floors follow by etching with Ground Zero Prepare, then thoroughly rinse with water. If floor has been previously coated, a small area should be cleaned and roughed up by a screen disking with a 80 grit screen. Test ZeroStat Crete for adhesion, lifting etc. Any area’s of the existing coating which display poor adhesion should be stripped. Wash the stripped area’s, acid etch, and rinse thoroughly. Allow the floor to dry. Catalyzed ZeroStat Crete should be used within six hours of mixing, therefore prepare only the quantity necessary for immediate use. Add the pre-measured catalyst to epoxy base. Stir gently until the catalyst has been thoroughly mixed in. Allow catalyzed mixture to stand 5 minutes. Apply catalyzed ZeroStat Crete with a short nap roller in thin uniform coats. The initial coat will cover approximately 250 to 500 ft2 per gallon. Second coat coverage is approximately 400 to 600 ft 2 per gallon . Note: This product is not recommended for applications that experience reoccurring standing water.

ZeroStat Crete is a thin set epoxy (approximately 3 to 7 mil thickness), much tougher and longer lasting that ESD paints. Due to it’s reduced solids count and thin set benefits ZeroStat Crete may exhibit slight variances in texture and color. These variances do not affect the excellent electrical performance or wear characteristics. ZeroStat Crete is only available in Gray and features a non glare finish. For extended color options and fill applications (up to 125 mil thickness) please give us a call.

Technical Documents:

Color Chart

Should you need a custom color or a Mix of colors we can assist with color matching. Their may be a price change and or Minimum order size for custom colors.

Request a Quote Above or call

FAX: 941-751-7586
Toll Free: 1-877-GND-ZERO (463-9376)